View SP508_318482.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
SP508
Rugged 20Mbps, 8 Channel Multi-Protocol Transceiver with Programmable DCE/DTE and Termination Resistors
FEATURES 20Mbps Differential Transmission Rates 15kV ESD Tolerance for Analog I/Os Internal Transceiver Termination Resistors for V.11/V.35 Interface Modes:
RS-232 (V.28) X.21 (V.11) RS-449/V.36 (V.10 & V.11) EIA-530 (V.10 & V.11) EIA-530A (V.10 & V.11) V.35
Now Available in Lead Free Packaging
Refer to page 7 for pinout Easy Flow-Through Pinout +5V Only Operation Individual Driver/Receiver Enable/Disable Controls Operates in DTE or DCE Mode
APPLICATIONS Router Software Selectable Protocols with 3-Bit Word Frame Relay Eight Drivers and Eight Receivers CSU V.35/V.11 Receiver Termination Network DSU Disable Option PBX Internal Line or Digital Loopback Testing Adheres to NET1/NET2 and TBR-2 Requirements Secure Communication Terminals
DESCRIPTION The SP508 is a monolithic device that supports eight (8) popular serial interface standards for Wide Area Network (WAN) connectivity. The SP508 is fabricated using a low power BiCMOS process technology, and incorporates a Sipex regulated charge pump allowing +5V only operation. Sipex's patented charge pump provides a regulated output of +5.8V, which will provide enough voltage for compliant operation in all modes. Eight (8) drivers and eight (8) receivers can be configured via software for any of the above interface modes at any time. The SP508 requires no additional external components for compliant operation for all of the eight (8) modes of operation other than four capacitors used for the internal charge pump. All necessary termination is integrated within the SP508 and is switchable when V.35 drivers and V.35 receivers, or when V.11 receivers are used. The SP508 provides the controls and transceiver availability for operating as either a DTE or DCE. Additional features with the SP508 include internal loopback that can be initiated in any of the operating modes by use of the LOOPBACK pin. While in loopback mode, receiver outputs are internally connected to driver inputs creating an internal signal path bypassing the serial communications controller for diagnostic testing. The SP508 also includes a latch enable pin with the driver and receiver address decoder. The internal V.11 or V.35 receiver termination can be switched off using a control pin (TERM_OFF) for monitoring applications. All eight (8) drivers and receivers in the SP508 include separate enable pins for added convenience. The SP508 is ideal for WAN serial ports in networking equipment such as routers, access concentrators, network muxes, DSU/CSU's, networking test equipment, and other access devices.
Applicable U.S. Patents-5,306,954; and others patents pending
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
1
ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability.
VCC ................................................................................................ +7V Input Voltages: Logic ................................................ -0.3V to (VCC+0.5V) Drivers ............................................. -0.3V to (VCC+0.5V) Receivers ........................................................... 15.5V Output Voltages: Logic ................................................ -0.3V to (VCC+0.5V) Drivers ................................................................... 12V Receivers ........................................ -0.3V to (VCC+0.5V) Storage Temperature ................................................ -65C to +150C Power Dissipation ................................................................. 1520mW (derate 19.0mW/C above +70C)
STORAGE CONSIDERATIONS
Due to the relatively large package size, storage in a low humidity environment is preferred. Large high density plastic packages are moisture sensitive and should be stored in Dry Vapor Barrier Bags. Prior to usage, the parts should remain bagged and stored below 40C and 60%RH. If the parts are removed from the bag, they should be used within 48 hours or stored in an environment at or below 20%RH. If the above conditions cannot be followed, the parts should be baked for four hours at 125C in order to remove moisture prior to soldering. Sipex ships the 100-pin LQFP in Dry Vapor Barrier Bags with a humidity indicator card and desiccant pack. The humidity indicator should be below 30%RH.
Package Derating:
oJA
.................................................................................................................
52.7 C/W
oJC .................................................................................................................... 6.5 C/W
ELECTRICAL SPECIFICATIONS
TA = 0C to +70C and VCC = +4.75V to +5.25V unless otherwise noted. The denotes the specifications which applies to full temperature range of -40C to =+85C, unless otherwise specified.
PARAMETER LOGIC INPUTS
VIL VIH
MIN.
TYP.
MAX.
0.8
UNITS
Volts Volts Volts Volts
CONDITIONS
2.0 0.4 2.4
LOGIC OUTPUTS
VOL VOH IOUT= -3.2mA IOUT= 1.0mA
V.28 DRIVER
DC Parameters Outputs Open Circuit Voltage Loaded Voltage Short-Circuit Current Power-Off Impedance AC Parameters Outputs Transition Time Instantaneous Slew Rate Propagation Delay tPHL tPLH Max.Transmission Rate 15 15 100 Volts Volts mA s V/s s s kbps per Figure 1 per Figure 2 per Figure 4, VOUT=0V per Figure 5 VCC = +5V for AC parameters per Figure 6; +3V to -3V per Figure 3
5.0 300
1.5 30 0.5 0.5 120 1 1 230 5 5
V.28 RECEIVER
DC Parameters Inputs Input Impedance Open-Circuit Bias HIGH Threshold LOW Threshold AC Parameters Propagation Delay tPHL tPLH 3 0.8 50 50 1.7 1.2 100 100 7 +2.0 3.0 k Volts Volts Volts ns ns per Figure 7 per Figure 8 VCC = +5V for AC parameters 500 500
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
2
ELECTRICAL SPECIFICATIONS
TA = 0C to +70C and VCC = +4.75V to +5.25V unless otherwise noted. The denotes the specifications which applies to full temperature range of -40C to =+85C, unless otherwise specified.
PARAMETER V.28 RECEIVER (cont)
AC Parameters (cont.) Max.Transmission Rate
MIN.
TYP.
MAX. UNITS
CONDITIONS
120
235
kbps
V.10 DRIVER
DC Parameters Outputs Open Circuit Voltage Test-Terminated Voltage Short-Circuit Current Power-Off Current AC Parameters Outputs Transition Time Propagation Delay tPHL tPLH Max.Transmission Rate 4.0 0.9VOC 6.0 150 100 200 30 30 120 100 100 500 500 Volts Volts mA A ns ns ns kbps per Figure 9 per Figure 10 per Figure 11 per Figure 12 VCC = +5V for AC parameters per Figure 13; 10% to 90%
V.10 RECEIVER
DC Parameters Inputs Input Current Input Impedance Sensitivity AC Parameters Propagation Delay tPHL tPLH Max.Transmission Rate -3.25 4 +3.25 0.3 60 60 120 mA k Volts ns ns kbps per Figures 14 and 15 VCC = +5V for AC parameters
V.11 DRIVER
DC Parameters Outputs Open Circuit Voltage Test Terminated Voltage Balance Offset Short-Circuit Current Power-Off Current AC Parameters Outputs Transition Time Propagation Delay tPHL tPLH Differential Skew (|tphl -tplh|) Max.Transmission Rate Channel to Channel Skew 6.0 2.0 0.5VOC 0.67VOC 0.4 +3.0 150 100 10 30 30 5 20 2 60 60 10 Volts Volts Volts Volts Volts mA A ns ns ns ns Mbps ns per Figure 16 per Figure 17 per Figure 17 per Figure 17 per Figure 18 per Figure 19 VCC = +5V for AC parameters per Fig. 21 and 36; 10% to 90% Using CL = 50pF; per Figures 33 and 36 per Figures 33 and 36 per Figures 33 and 36
V.11 RECEIVER
DC Parameters Inputs Common Mode Range Sensitivity -7 +7 0.2 Volts Volts
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
3
ELECTRICAL SPECIFICATIONS
TA = 0C to +70C and VCC = +4.75V to +5.25V unless otherwise noted. The denotes the specifications which applies to full temperature range of -40C to =+85C, unless otherwise specified.
PARAMETER V.11 RECEIVER (cont)
DC Parameters (cont.) Input Current Current w/ 100 Termination Input Impedance AC Parameters Propagation Delay tPHL tPLH Skew(|tphl-tplh|) Max.Transmission Rate Channel to Channel Skew
MIN.
TYP.
MAX. UNITS
CONDITIONS
-3.25 4 30 30 5 20 2
3.25 60.75
mA mA k ns ns ns Mbps ns

per Figure 20 and 22; power on or off per Figure 23 and 24 VCC = +5V for AC parameters Using CL = 50pF; per Figures 33 and 38 per Figures 33 and 38 per Figure 33
60 60 10
V.35 DRIVER
DC Parameters Outputs Test Terminated Voltage Offset Output Overshoot Source Impedance Short-Circuit Impedance AC Parameters Outputs Transition Time Propagation Delay tPHL tPLH Differential Skew (|tphl-tplh|) Max.Transmission Rate Channel to Channel Skew 0.44 -0.2VST 50 135 7 30 30 5 20 5 0.66 0.6 +0.2VST 150 165 20 60 60 10 Volts Volts Volts ns ns ns ns Mbps ns per Figure 25 per Figure 25 per Figure 25; VST = Steady state value per Figure 27; ZS = V2/V1 x 50 per Figure 28 VCC = +5V for AC parameters per Figure 29; 10% to 90% per Figure 33 and 36; CL = 20pF per Figure 33 and 36; CL = 20pF per Figure 33 and 36; CL = 20pF

V.35 RECEIVER
DC Parameters Inputs Sensitivity Source Impedance Short-Circuit Impedance AC Parameters Propagation Delay tPHL tPLH Skew(|tphl-tplh|) Max.Transmission Rate Channel to Channel Skew Driver Output 3-State Current Rcvr Output 3-State Current 50 90 135 30 30 5 20 2 500 1 +200 110 165 60 60 10 mV ns ns ns Mbps ns A A
per Figure 30; ZS = V2/V1 x 50 per Figure 31 VCC = +5V for AC parameters per Figure 33 and 38; CL = 20pF per Figure 33 and 38; CL = 20pF per Figure 33; CL = 20pF
TRANSCEIVER LEAKAGE CURRENT
10 per Figure 32; Drivers disabled TX & RX disabled, 0.4V - VO - 2.4V
POWER REQUIREMENTS
VCC ICC (Shutdown Mode) (V.28/RS-232) (V.11/RS-422) (EIA-530 & RS-449) (V.35) (EIA-530A) 4.75 5.00 1 95 230 270 170 200 5.25 Volts A mA mA mA mA mA All ICC values are with VCC = +5V fIN = 120kbps; Drivers active & loaded fIN = 10Mbps; Drivers active & loaded fIN = 10Mbps; Drivers active & loaded V.35 @ fIN = 10Mbps, V.28 @ 20kbps fIN = 10Mbps; Drivers active & loaded
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
4
OTHER AC CHARACTERISTICS
TA = +25C and VCC = +5.0V unless otherwise noted.
PARAMETER MIN. TYP. MAX. UNITS CONDITIONS DRIVER DELAY TIME BETWEEN ACTIVE MODE AND TRI-STATE MODE
RS-232/V.28 tPZL; Tri-state to Output LOW tPZH; Tri-state to Output HIGH tPLZ; Output LOW to Tri-state tPHZ; Output HIGH to Tri-state RS-423/V.10 tPZL; Tri-state to Output LOW tPZH; Tri-state to Output HIGH tPLZ; Output LOW to Tri-state tPHZ; Output HIGH to Tri-state RS-422/V.11 tPZL; Tri-state to Output LOW tPZH; Tri-state to Output HIGH tPLZ; Output LOW to Tri-state tPHZ; Output HIGH to Tri-state V.35 tPZL; Tri-state to Output LOW tPZH; Tri-state to Output HIGH tPLZ; Output LOW to Tri-state tPHZ; Output HIGH to Tri-state RS-232/V.28 tPZL; Tri-state to Output LOW tPZH; Tri-state to Output HIGH tPLZ; Output LOW to Tri-state tPHZ; Output HIGH to Tri-state RS-423/V.10 tPZL; Tri-state to Output LOW tPZH; Tri-state to Output HIGH tPLZ; Output LOW to Tri-state tPHZ; Output HIGH to Tri-state 0.11 0.11 0.05 0.05 0.07 0.05 0.55 0.12 0.04 0.05 0.03 0.11 0.85 0.36 0.06 0.05 5.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 10.0 2.0 2.0 2.0 10.0 2.0 2.0 2.0 s s s s s s s s s s s s s s s s CL = 100pF, Fig. 34 & 40; S2 closed CL = 100pF, Fig. 34 & 40; S2 closed CL = 100pF, Fig. 34 & 40; S2 closed CL = 100pF, Fig. 34 & 40; S2 closed CL = 100pF, Fig. 34 & 40; S2 closed CL = 100pF, Fig. 34 & 40; S2 closed CL = 100pF, Fig. 34 & 40; S2 closed CL = 100pF, Fig. 34 & 40; S2 closed CL = 100pF, Fig. 34 & 37; S1 closed CL = 100pF, Fig. 34 & 37; S2 closed CL = 15pF, Fig. 34 & 37; S1 closed CL = 15pF, Fig. 34 & 37; S2 closed CL = 100pF, Fig. 34 & 37; S1 closed CL = 100pF, Fig. 34 & 37; S2 closed CL = 15pF, Fig. 34 & 37; S1 closed CL = 15pF, Fig. 34 & 37; S2 closed
RECEIVER DELAY TIME BETWEEN ACTIVE MODE AND TRI-STATE MODE
0.05 0.05 0.65 0.65 0.04 0.03 0.03 0.03 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 s s s s s s s s CL = 100pF, Fig. 35 & 40; S1 closed CL = 100pF, Fig. 35 & 40; S2 closed CL = 100pF, Fig. 35 & 40; S1 closed CL = 100pF, Fig. 35 & 40; S2 closed CL = 100pF, Fig. 35 & 40; S1 closed CL = 100pF, Fig. 35 & 40; S2 closed CL = 100pF, Fig. 35 & 40; S1 closed CL = 100pF, Fig. 35 & 40; S2 closed
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
5
OTHER AC CHARACTERISTICS (Continued)
TA = +25C and VCC = +5.0V unless otherwise noted.
PARAMETER
RS-422/V.11 tPZL; Tri-state to Output LOW tPZH; Tri-state to Output HIGH tPLZ; Output LOW to Tri-state tPHZ; Output HIGH to Tri-state V.35 tPZL; Tri-state to Output LOW tPZH; Tri-state to Output HIGH tPLZ; Output LOW to Tri-state tPHZ; Output HIGH to Tri-state
MIN.
TYP.
0.04 0.03 0.03 0.03 0.04 0.03 0.03 0.03
MAX. UNITS
2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 s s s s s s s s
CONDITIONS
CL = 100pF, Fig. 35 & 39; S1 closed CL = 100pF, Fig. 35 & 39; S2 closed CL = 15pF, Fig. 35 & 39; S1 closed CL = 15pF, Fig. 35 & 39; S2 close CL = 100pF, Fig. 35 & 39; S1 closed CL = 100pF, Fig. 35 & 39; S2 closed CL = 15pF, Fig. 35 & 39; S1 closed CL = 15pF, Fig. 35 & 39; S2 closed
TRANSCEIVER TO TRANSCEIVER SKEW RS-232 Driver RS-232 Receiver RS-422 Driver RS-422 Receiver RS-423 Driver RS-423 Receiver V.35 Driver V.35 Receiver 100 100 20 20 2 2 2 3 5 5 5 5 2 2 2 2
(per Figures 32, 33, 36, 38) ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns [ (tphl )Tx1 - (tphl )Txn ] [ (tplh )Tx1 - (tplh )Txn] [ (tphl )Rx1 - (tphl )Rxn ] [ (tphl )Rx1 - (tphl )Rxn ] [ (tphl )Tx1 - (tphl )Txn ] [ (tplh )Tx1 - (tplh )Txn ] [ (tphl )Rx1 - (tphl )Rxn ] [ (tphl )Rx1 - (tphl )Rxn ] [ (tphl )Tx2 - (tphl )Txn ] [ (tplh )Tx2 - (tplh )Txn ] [ (tphl )Rx2 - (tphl )Rxn ] [ (tphl )Rx2 - (tphl )Rxn ] [ (tphl )Tx1 - (tphl )Txn ] [ (tplh )Tx1 - (tplh )Txn ] [ (tphl )Rx1 - (tphl )Rxn ] [ (tphl )Rx1 - (tphl )Rxn]
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
6
PINOUT 100 PIN LQFP
99 V35TGND1
94 V35TGND2
89 V35TGND3
81 RRC(a)
79 RRC(b)
100 SD(b)
97 SD(a)
85 RS(b)
83 RS(a)
90 ST(b)
87 ST(a)
95 TT(b)
92 TT(a)
78 TR(b)
96 GND
91 GND
86 GND
82 GND
98 VCC
93 VCC
88 VCC
84 VCC
80 VCC
77 VCC
VCC 1 GND 2 SDEN 3 TTEN 4 STEN 5 RSEN 6 TREN 7 RRCEN 8 RLEN 9 LLEN 10 RDEN 11 RTEN 12 TXCEN 13 CSEN 14 DMEN15 RRTEN 16 ICEN 17 TMEN 18 D0 19 D1 20 D2 21 TERM_OFF 22 D_LATCH 23 N/C 24 GND 25
(R)
76 N/C
75 TR(a) 74 GND 73 VDD 72 C1+ 71 VCC 70 C2+ 69 C168 GND 67 C266 VSS 65 RL(a) 64 VCC 63 LL(a) 62 TM(a) 61 IC(a)
SP508
60 RRT(a) 59 RRT(b) 58 V10GND 57 DM(a) 56 DM(b) 55 CS(a) 54 CS(b) 53 TXC(a) 52 GND 51 TXC(b)
ST 30 RTS 31
LOOPBACK 27
TXD 28
TXCE 29
DTR 32
TXC 38
CTS 39
TM 43
RI 42
RT(b) 49
RD(b) 47
DCD_DTE 41
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
DCD_DCE 33
V35RGND 46
RD(a) 48
7
RT(a) 50
RL 34
VCC 26
LL 35
RXD 36
RXC 37
DSR 40
GND 44
VCC 45
(c) Copyright 2004 Sipex Corporation
PIN DESCRIPTION
Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Pin Name VCC GND SDEN TTEN STEN RSEN TREN RRCEN RLEN LLEN# RDEN# RTEN# TxCEN# CSEN# DMEN# RRTEN# ICEN# TMEN D0 D1 D2 D_LATCH# NC GND VCC TxD TxCE ST RTS DTR DCD_DCE RL LL RxD RxC TxC CTS DSR DCD_DTE RI TM GND VCC V35RGND RD(b) RD(a) RT(b) RT(a) Description 5V Power Supply Input Signal Ground TxD Driver Enable Input TxCE Driver Enable Input ST Driver Enable Input RTS Driver Enable Input DTR Driver Enable Input DCD Driver Enable Input RL Driver Enable Input LL Driver Enable Input RxD Receiver Enable Input RxC Receiver Enable Input TxC Receiver Enable Input CTS Receiver Enable Input DSR Receiver Enable Input DCDDTE Receiver Enable Input RI Receiver Enable Input TM Receiver Enable Input Mode Select Input Mode Select Input Mode Select Input Decoder Latch Input No Connect Signal Ground 5V Power Supply Input TxD Driver TTL Input TxCE Driver TTL Input ST Driver TTL Input RTS Driver TTL Input DTR Driver TTL Input DCDDCE Driver TTL Input RL Driver TTL Input LL Driver TTL Input RxD Receiver TTL Output RxC Receiver TTLOutput TxC Receiver TTL Output CTS Receiver TTL Output DSR Receiver TTL Output DCDDTE Receiver TTL Output RI Receiver TTL Output TM Receiver TTL Output Signal Ground Power Supply Input Reciever Termination Refrence RXD Non-Inverting Input RXD Inverting Input RxC Non-Inverting Input RxC Inverting Input Pin Number 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Pin Name TxC(b) GND TxC(a) CS(b) CS(a) DM(b) DM(a) GNDV10 RRT(b) RRT(a) IC TM(a) LL(a) VCC RL(a) VSS1 C2N GND C1N C2P VCC C1P VDD GND TR(a) NC VCC TR(b) RRC(b) VCC RRC(a) GND RS(a) VCC RS(b) GND ST(a) VCC ST(b) GND TT(a) VCC TT(b) GND SD(a) VCC SD(b) Description TxC Non-Inverting Input Signal Ground TxC Inverting Input CTS Non-Inverting Input CTS Inverting Input DSR Non-Inverting Input DSR Inverting Input V.10 Rx Reference Node DCDDTE Non-Inverting Input DCDDTE Inverting Input RI Receiver Input TM Receiver Input LL Driver Output Power Supply Input RL Driver Output -2xVCC Charge Pump Output Charge Pump Capacitor Signal Ground Charge Pump Capacitor Charge Pump Capacitor Power Supply Input Charge Pump Capacitor 2xVCC Charge Pump Output Signal Ground DTR Inverting Output No Connect Power Supply Input DTR Non-Inverting Output DCD Non-Inverting Output Power Supply Input DCD Inverting Output Signal Ground RTS Inverting Output Power Supply Input RTS Non-Inverting Output Signal Ground ST Inverting Output Power Supply Input ST Non-Inverting Output Signal Ground TxCE Inverting Output 5V Power Supply Input TxCE Non-Inverting Output Signal Ground TxD Inverting Output 5V Power Supply Input TxD Non-Inverting Output
TERM_OFF Termination Disable Input
LOOPBACK# Loopback Mode Enable Input
V35TGND3 ST Termination Referance
V35TGND2 ST Termination Referance
V35TGND1 ST Termination Referance
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
8
SP508 Pin Designation
SP508CF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Date: 8/19/04
SP508CB A2 B2 B1 C2 D1 E2 F1 F3 G2 G1 G3 H3 H1 H2 J2 J3 K1 K2 L1 L2 L3 M2 N1 P1 P2 P3 N3 M3 N4 P4 M4 N5 P5 M5 N6 M6 N7 P7 M7 P8 N8 P9 M9 P10 N10 M10 P11 N11 M11
DESIG VCC GND SDEN TTEN STEN RSEN TREN RRCEN RLEN LLEN# RDEN# RTEN# TxCEN# CSEN# DMEN# RRTEN# ICEN# TMEN D0 D1 D2 TERM_OFF D_LATCH# N/C GND VCC LOOPBACK# TxD TxCE ST RTS DTR DCD_DCE RL LL RxD RxC TxC CTS DSR DCD_DTE RI TM GND VCC V35RGND RD(B) RD(A) RT(B) RT(A)
SP508CF 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
SP508CB N12 N13 M14 M13 L14 K14 J14 J12 H13 H14 H12 G12 G14 G13 F14 F13 F12 E14 E13 D14 D13 C14 B14 A14 A13 A12 B12 C12 B11 A11 C11 B10 A10 C10 A9 C9 A8 C8 A7 B7 A6 B6 C6 A5 B5 C5 B4 C4 B3
DESIG TxC(B) GND TxC(A) CS(B) CS(A) DM(B) DM(A) V10GND RRT(B) RRT(A) IC(A) TM(A) LL(A) VCC RL(A) VSS C2GND C1C2+ VCC C1+ VDD GND TR(A) NC VCC TR(B) RRC(A) VCC RRC(A) GND RS(A) VCC RS(B) GND ST(A) VCC V35TGND3 ST(B) GND TT(A) VCC V35TGND2 TT(B) GND SD(A) VCC V35TGND1 SD(B)
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
9
SP508 Driver Table
Driver Output Pin MODE (D0, D1, D2) T1OUT(a) T1OUT(b) T2OUT(a) T2OUT(b) T3OUT(a) T3OUT(b) T4OUT(a) T4OUT(b) T5OUT(a) T5OUT(b) T6OUT(a) T6OUT(b) T7OUT(a) T8OUT(a) V.35 Mode 001 V.35 V.35 V.35 V.35 V.35 V.35 V.28 High-Z V.28 High-Z V.28 High-Z V.28 V.28 EIA-530 Mode 010 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.10 V.10 RS-232 Mode (V.28) 011 V.28 High-Z V.28 High-Z V.28 High-Z V.28 High-Z V.28 High-Z V.28 High-Z V.28 V.28 EIA-530A Mode 100 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.10 High-Z V.11 V.11 V.10 V.10 RS-449 Mode (V.36) 101 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.10 V.10 X.21 Mode (V.11) 110 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 High-Z High-Z Shutdown 111 High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z TxD(a) TxD(b) TxCE(a) TxCE(b) TxC_DCE(a) TxC_DCE(b) RTS(a) RTS(b) DTR(a) DTR(b) DCD_DCE(a) DCD_DCE(b) RL LL Suggested Signal
Table 1. Driver Mode Selection
SP508 Receiver Table
Receiver Input Pin MODE (D0, D1, D2) R1IN(a) R1IN(b) R2IN(a) R2IN(b) R3IN(a) R3IN(b) R4IN(a) R4IN(b) R5IN(a) R5IN(b) R6IN(a) R6IN(b) R7IN(a) R8IN(a) V.35 Mode 001 V.35 V.35 V.35 V.35 V.35 V.35 V.28 High-Z V.28 High-Z V.28 High-Z V.28 V.28 EIA-530 Mode 010 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.10 V.10 RS-232 Mode (V.28) 011 V.28 High-Z V.28 High-Z V.28 High-Z V.28 High-Z V.28 High-Z V.28 High-Z V.28 V.28 EIA-530A Mode 100 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.10 High-Z V.11 V.11 V.10 V.10 RS-449 Mode (V.36) 101 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.10 V.10 X.21 Mode (V.11) 110 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 High-Z High-Z Shutdown 111 High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z High-Z RxD(a) RxD(b) RxC(a) RxC(b) TxC_DTE(a) TxC_DTE(b) CTS(a) CTS(b) DSR(a) DSR(b) DCD_DTE(a) DCD_DTE(b) RI TM Suggested Signal
Table 2. Receiver Mode Selection
Date: 8/19/04 SP508 Enhanced WAN Multi-Protocol Serial Transceiver (c) Copyright 2004 Sipex Corporation
10
TEST CIRCUITS
A
A
VOC
3k
VT
C
C
Figure 1. V.28 Driver Output Open Circuit Voltage
Figure 2. V.28 Driver Output Loaded Voltage
A
A
7k
VT
Oscilloscope
Isc
C
Scope used for slew rate measurement.
C
Figure 3. V.28 Driver Output Slew Rate
Figure 4. V.28 Driver Output Short-Circuit Current
VCC = 0V
A Ix
A
2V
3k
2500pF
Oscilloscope
C
C
Figure 5. V.28 Driver Output Power-Off Impedance
Figure 6. V.28 Driver Output Rise/Fall Times
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
11
A A Iia
15V
voc
C C
Figure 7. V.28 Receiver Input Impedance
Figure 8. V.28 Receiver Input Open Circuit Bias
A
A
3.9k
VOC
450
Vt
C
C
Figure 9. V.10 Driver Output Open-Circuit Voltage
Figure 10. V.10 Driver Output Test Terminated Voltage
VCC = 0V
A
A Ix
0.25V
Isc
C
C
Figure 11. V.10 Driver Output Short-Circuit Current
Figure 12. V.10 Driver Output Power-Off Current
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
12
A
A Iia
10V
450
Oscilloscope
C
C
Figure 13. V.10 Driver Output Transition Time
Figure 14. V.10 Receiver Input Current
A
V.10 RECEIVER +3.25mA
3.9k VOC
VOCB VOCA
-10V
-3V
B
+3V
+10V
C
Maximum Input Current vesus Voltage -3.25mA
Figure 15. V.10 Receiver Input IV Graph
Figure 16. V.11 Driver Output Open-Circuit Voltage
A
A Isa 50 VT 50 Isb B
B
V
OS
C
C
Figure 17. V.11 Driver Output Test Terminated Voltage
Figure 18. V.11 Driver Output Short-Circuit Current
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
13
VCC = 0V
A
A Ixa
0.25V
Iia
10V
B
B
C
C
VCC = 0V
A
A
0.25V
10V
Ixb B
Iib B
C
C
Figure 19. V.11 Driver Output Power-Off Current
Figure 20. V.11 Receiver Input Current
A
V.11 RECEIVER
50
Oscilloscope
+3.25mA
50
B
50
VE
-10V
-3V +3V +10V
C
Maximum Input Current vesus Voltage -3.25mA
Figure 21. V.11 Driver Output Rise/Fall Time Figure 22. V.11 Receiver Input IV Graph
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
14
A Iia
6V
V.11 RECEIVER
w/ Optional Cable Termination (100 to 150) i [mA] = V [V] / 0.1
100 to 150
i [mA] = V [V] - 3) / 4.0 -6V
-3V +3V +6V
B
i [mA] = V [V] - 3) / 4.0
C
i [mA] = V [V] / 0.1
Maximum Input Current versus Voltage
Figure 24. V.11 Receiver Input Graph w/ Termination
A
6V
100 to 150
A
50
Iib B
B
VT 50 VOS
C
C
Figure 23. V.11 Receiver Input Current w/ Termination
Figure 25. V.35 Driver Output Test Terminated Voltage
A
V1 A 50
VCC
24kHz, 550mVp-p Sine Wave
V2
B
C
B
Figure 26. V.35 Driver Output Offset Voltage
Date: 8/19/04
Figure 27. V.35 Driver Output Source Impedance
(c) Copyright 2004 Sipex Corporation
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
15
A
A 50
Oscilloscope
B
ISC
50 B 50
2V
C
C
Figure 28. V.35 Driver Output Short-Circuit Impedance
Figure 29. V.35 Driver Output Rise/Fall Time
A
V1 A 50
24kHz, 550mVp-p Sine Wave
V2
B
B
Isc
2V
C
C
Figure 30. V.35 Receiver Input Source Impedance
Figure 31. V.35 Receiver Input Short-Circuit Impedance
Any one of the three conditions for disabling the driver.
VCC = 0V
1
1
1
D2
D1
D0
A IZSC 12V
VCC
CL1 TIN B A CL2
B ROUT A 15pF
Logic "1"
fIN (50% Duty Cycle, 2.5VP-P)
B
Figure 32. Driver Output Leakage Current Test
Figure 33. Driver/Receiver Timing Test Circuit
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
16
Output Under Test
500 CL
S1
VCC
Receiver Output CRL
Test Point S1 1K S2
1K VCC
S2
Figure 34. Driver Timing Test Load Circuit
Figure 35. Receiver Timing Test Load Circuit
f > 10MHz; tR < 10ns; tF < 10ns DRIVER INPUT +3V 1.5V 0V A B tDPLH DIFFERENTIAL OUTPUT VB - VA VO+ 0V VO- tDPHL VO 1/2VO tPLH tPHL 1/2VO 1.5V
DRIVER OUTPUT
tR
tF
tSKEW = | tDPLH - tDPHL |
Figure 36. Driver Propagation Delays
Mx or Tx_Enable
+3V 1.5V 0V 5V tZL 2.3V VOL VOH Output normally LOW 1.5V tLZ 0.5V 0.5V tHZ
A, B
A, B 0V
2.3V tZH
Output normally HIGH
Figure 37. Driver Enable and Disable Times
f > 10MHz; tR < 10ns; tF < 10ns V0D2+ A-B V0D2- VOH RECEIVER OUT VOL tSKEW = | tPHL - tPLH | tPLH (VOH - VOL)/2 tPHL 0V INPUT OUTPUT (VOH - VOL)/2 0V
Figure 38. Receiver Propagation Delays
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
17
f = 1MHz; tR < 10ns; tF < 10ns DECx +3V 1.5V RCVRENABLE RECEIVER OUT VIL VIH RECEIVER OUT 0V 1.5V tZH Output normally HIGH 0V 5V 1.5V Output normally LOW 0.5V 0.5V tHZ tZL 1.5V tLZ
Figure 39. Receiver Enable and Disable Times
+3V Tx_Enable 0V 0V TOUT VOL
f = 60kHz; tR < 10ns; tF < 10ns 1.5V tZL VOL - 0.5V Output LOW 1.5V tLZ
VOL - 0.5V
+3V Tx_Enable 0V VOH TOUT 0V
f = 60kHz; tR < 10ns; tF < 10ns 1.5V tZH Output HIGH 1.5V tHZ VOH - 0.5V
Figure 40. V.28 (RS-232) and V.10 (RS-423) Driver Enable and Disable Times
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
18
Figure 41. Typical V.28 Driver Output Waveform
Figure 42. Typical V.10 Driver Output Waveform
Figure 43. Typical V.11 Driver Output Waveform
Figure 44. Typical V.35 Driver Output Waveform
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
19
VCC pins (1, 26, 45, 64, 71, 77, 80, 84, 88, 93, 98) GND pins (2, 25, 44, 52, 68, 74, 82, 86, 91, 96) N.C. pins (24 and 76)
+5V (decoupling capacitor not shown)
1F
1F
1F
72
VCC
C1+
69
C1-
70
C2+
67
C2-
73 VDD
V35RGND RD(a) RxD RDEN RD(b) RT(a) RxC RTEN RT(b) TxC(a) TxC TxCEN TxC(b) CS(a) CTS CSEN CS(b) DM(a) DSR DMEN DM(b) RRT(a) DCD_DTE RRTEN RRT(b) IC RI ICEN
VSS
Regulated Charge Pump
66
1F
46 48 36 11 47 50 37 12 49 53 38 13 51 55 39 14 54 57 40 15 56 60 41 16 59 61 42 17 62
28 97 99 100 3 29 92 94 95 4 30 87 89 90 5 31 83 85 6 32 75 78 7 33 81 79 8 34 65 9
TxD SD(a) V35TGND1 SD(b) SDEN TxCE TT(a) V35TGND2 TT(b) TTEN ST ST(a) V35TGND3 ST(b) STEN RTS RS(a) RS(b) RSEN DTR TR(a) TR(b) TREN DCD_DCE RRC(a) RRC(b) RRCEN RL RL(a) RLEN LL LL(a) LLEN
TM(a) TM TMEN
35 63 10
43 18
19 20 21 23 22 27
D0 D1 D2 D-LATCH TERM-OFF LOOPBACK GND
SP508
V.10-GND
58
RECEIVER TERMINATION NETWORK
V.35 MODE V.11 MODE RX ENABLE 51ohms 51ohms 124ohms
V.35 DRIVER TERMINATION NETWORK
51ohms V.35 MODE TX ENABLE 51ohms 124ohms
Figure 45. Functional Diagram
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
20
The SP508 contains highly integrated serial transceivers that offer programmability between interface modes through software control. The SP508 offers the hardware interface modes for RS-232 (V.28), RS-449/V.36 (V.11 and V.10), EIA-530 (V.11 and V.10), EIA-530A (V.11 and V.10), V.35 (V.35 and V.28) and X.21(V.11). The interface mode selection is done via three control pins, which can be latched via microprocessor control. The SP508 has eight drivers, eight receivers, and Sipex's patented on-board charge pump (5,306,954) that is ideally suited for wide area network connectivity and other multi-protocol applications. Other features include digital and line loopback modes, individual enable/disable control lines for each driver and receiver, fail-safe when inputs are either open or shorted, individual termination resistor ground paths, separate driver and receiver ground outputs, enhanced ESD protection on driver outputs and receiver inputs. THEORY OF OPERATION The SP508 device is made up of 1) the drivers, 2) the receivers, 3) a charge pump, 4) DTE/DCE switching algorithm, and 5) control logic. Drivers The SP508 has eight enhanced independent drivers. Control for the mode selection is done via a threebit control word into D0, D1, and D2. The drivers are prearranged such that for each mode of operation, the relative position and functionality of the drivers are set up to accommodate the selected interface mode. As the mode of the drivers is changed, the electrical characteristics will change to support the required signal levels. The mode of each driver in the different interface modes that can be selected is shown in Table 1.
FEATURES There are four basic types of driver circuits - ITU-T-V.28 (RS-232), ITU-T-V.10 (RS-423), ITU-T-V.11 (RS-422), and CCITT-V.35. The V.28 (RS-232) drivers output single-ended signals with a minimum of +5V (with 3k & 2500pF loading), and can operate over 120kbps. Since the SP508 uses a charge pump to generate the RS-232 output rails, the driver outputs will never exceed +10V. The V.28 driver architecture is similar to Sipex's standard line of RS-232 transceivers. The RS-423 (V.10) drivers are also single-ended signals which produce open circuit VOL and VOH measurements of +4.0V to +6.0V. When terminated with a 450 load to ground, the driver output will not deviate more than 10% of the open circuit value. This is in compliance of the ITU V.10 specification. The V.10 (RS-423) drivers are used in RS-449/V.36, EIA-530, and EIA-530A modes as Category II signals from each of their corresponding specifications. The V.10 drivers are guaranteed to transmit over 120kbps, but can operate at over 1Mbps if necessary. The third type of drivers are V.11 (RS-422) differential drivers. Due to the nature of differential signaling, the drivers are more immune to noise as opposed to single-ended transmission methods. The advantage is evident over high speeds and long transmission lines. The strength of the driver outputs can produce differential signals that can maintain +2V differential output levels with a load of 100. The signal levels and drive capability of these drivers allow the drivers to also support RS-485 requirements of +1.5V differential output levels with a 54 load. The strength allows the SP508 differential driver to drive over long cable lengths with minimal signal degradation. The V.11 drivers are used in RS-449, EIA-530, EIA-530A and V.36 modes as Category I signals which are used for clock and data. Sipex's new driver design over its predecessors allow the SP508 to operate over 20Mbps for differential transmission.
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
21
The fourth type of drivers are V.35 differential drivers. There are only three available on the SP508 for data and clock (TxD, TxCE, and TxC in DCE mode). These drivers are current sources that drive loop current through a differential pair resulting in a 550mV differential voltage at the receiver. These drivers also incorporate fixed termination networks for each driver in order to set the VOH and VOL depending on load conditions. This termination network is basically a "Y" configuration consisting of two 51 resistors connected in series and a 124 resistor connected between the two 50 resistors and a V35TGND output. Each of the three drivers and its associated termination will have its own V35TGND output for grounding convenience. Filtering can be done on these pins to reduce common mode noise transmitted over the transmission line by connecting a capacitor to ground. The drivers also have separate enable pins which simplifies half-duplex configurations for some applications, especially programmable DTE/DCE. The enable pins will either enable or disable the output of the drivers according to the appropriate active logic illustrated on Figure 45. The enable pins have internal pull-up and pulldown devices, depending on the active polarity of the receiver, that enable the driver upon poweron if the enable lines are left floating. During disabled conditions, the driver outputs will be at a high impedance 3-state. The driver inputs are both TTL or CMOS compatible. All driver inputs have an internal pull-up resistor so that the output will be at a defined state at logic LOW ("0"). Unused driver inputs can be left floating. The internal pull-up resistor value is approximately 500k. Receivers The SP508 has eight enhanced independent receivers. Control for the mode selection is done via a three-bit control word that is the same as the driver control word. Therefore, the modes for the drivers and receivers are identical in the application. Like the drivers, the receivers are prearranged for the specific requirements of the synchronous serial interface. As the operating mode of the receivers is changed, the electrical characteristics will change to support the required serial interface
Date: 8/19/04
protocols of the receivers. Table 2 shows the mode of each receiver in the different interface modes that can be selected. There are two basic types of receiver circuits--ITU-T-V .28 (RS-232) and ITU-T-V.11, (RS-422). The RS-232 (V.28) receiver is single-ended and accepts RS-232 signals from the RS-232 driver. The RS-232 receiver has an operating input voltage range of +15V and can receive signals downs to +3V. The input sensitivity complies with RS-232 and V .28 at +3V. The input impedance is 3k to 7k in accordance to RS232 and V .28. The receiver output produces a TTL/CMOS signal with a +2.4V minimum for a logic "1" and a +0.4V maximum for a logic "0". The RS-232 (V.28) protocol uses these receivers for all data, clock and control signals. They are also used in V.35 mode for control line signals: CTS, DSR, LL, and RL. The RS-232 receivers can operate over 120kbps. The second type of receiver is a differential type that can be configured internally to support ITU-T-V.10 and CCITT-V.35 depending on its input conditions. This receiver has a typical input impedance of 10k and a differential threshold of less than +200mV, which complies with the ITU-T-V.11 (RS-422) specifications. V.11 receivers are used in RS-449/V.36, EIA-530, EIA-530A and X.21 as Category I signals for receiving clock, data, and some control line signals not covered by Category II V.10 circuits. The differential V.11 transceiver has improved architecture that allows over 20Mbps transmission rates. Receivers dedicated for data and clock (RxD, RxC, TxC) incorporate internal termination for V.11. The termination resistor is typically 120 connected between the A and B inputs. The termination is essential for minimizing crosstalk and signal reflection over the transmission line . The minimum value is guaranteed to exceed 100, thus complying with the V.11 and RS-422 specifications. This resistor is invoked when the receiver is operating as a V.11 receiver, in modes EIA-530, EIA-530A, RS-449/V.36, and X.21.
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
22
The same receivers also incorporate a termination network internally for V.35 applications. For V.35, the receiver input termination is a "Y" termination consisting of two 51 resistors connected in series and a 124 resistor connected between the two 50 resistors and V35RGND output. The V35RGND is usually grounded. The receiver itself is identical to the V.11 receiver. The differential receivers can be configured to be ITU-T-V.10 single-ended receivers by internally connecting the non-inverting input to ground. This is internally done by default from the decoder. The non-inverting input is rerouted to V10GND and can be grounded separately. The ITU-T-V.10 receivers can operate over 1Mbps and are used in RS-449/V.36, E1A-530, E1A-530A and X.21 modes as Category II signals as indicated by their corresponding specifications. All receivers include an enable/disable line for disabling the receiver output allowing convenient half-duplex configurations. The enable pins will either enable or disable the output of the receivers according to the appropriate active logic illustrated on Figure 45. The receiver's enable lines include an internal pull-up or pull-down device, depending on the active polarity of the receiver, that enables the receiver upon power up if the enable lines are left floating. During disabled conditions, the receiver outputs will be at a high impedance state. If the receiver is disabled any associated termination is also disconnected from the inputs. All receivers include a fail-safe feature that outputs a logic high when the receiver inputs are open, terminated but open, or shorted together. For single-ended V.28 and V.10 receivers, there are internal 5k pull-down resistors on the inputs which produces a logic high ("1") at the receiver outputs. The differential receivers have a proprietary circuit that detect open or shorted inputs and if so, will produce a logic HIGH ("1") at the receiver output.
CHARGE PUMP The charge pump is a Sipex-patented design (5,306,954) and uses a unique approach compared to older less-efficient designs. The charge pump still requires four external capacitors, but uses four-phase voltage shifting technique to attain symmetrical power supplies. The charge pump VDD and VSS outputs are regulated to +5.8V and -5.8V, respectively. There is a free-running oscillator that controls the four phases of the voltage shifting. A description of each phase follows. Phase 1 __VSS charge storage ----During this phase of the clock cycle, the positive side of capacitors C1 and C2 are initially charged to VCC. C+ is then switched to ground and the charge in C1- is transferred to C2-. Since C2+ is connected to VCC, the voltage potential across capacitor C2 is now 2XVCC. Phase 2 --VSS transfer --Phase two of the clock connects the negative terminal of C2 to the VSS storage capacitor and the positive terminal of C2 to ground, and transfers the negative generated voltage to C3. This generated voltage is regulated to -5.8V. Simultaneously, the positive side of the capacitor C1 is switched to VCC and the negative side is connected to ground. Phase 3 --VDD charge storage --The third phase of the clock is identical to the first phase--the charge transferred in C1 produces -VCC in the negative terminal of C1 which is applied to the negative side of the capacitor C2 . Since C2+ is at VCC, the voltage potential across C2 is 2XVCC. Phase 4 --VDD transfer --The fourth phase of the clock connects the negative terminal of C2 to ground, and transfers the generated 5.8V across C2 to C4, the VDD storage capacitor. This voltage is regulated to +5.8V. At the regulated voltage, the internal oscillator is disabled and simultaneously with this, the positive side of capacitor C1 is switched to VCC and the negative side is connected to ground, and the cycle begins again. The charge pump cycle will continue as long as the operational conditions for the internal oscillator are present.
(c) Copyright 2004 Sipex Corporation
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
23
Since both V+ and V- are separately generated from VCC; in a no-load condition V+ and V- will be symmetrical. Older charge pump approaches that generate V- from V+ will show a decrease in the magnitude of V- compared to V+ due to the inherent inefficiencies in the design. The clock rate for the charge pump typically operates at 250kHz. The external capacitors can be as low as 1F with a 16V breakdown voltage rating. TERM_OFF FUNCTION The SP508 contains a TERM_OFF pin that disables all three receiver input termination networks regardless of mode. This allows the device to be used in monitor mode applications typically found in networking test equipment. The TERM_OFF pin internally contains a pull-down device with an impedance of over 500k, which will default in a "ON" condition during power-up if V.35 receivers are used. The individual receiver enable line and the SHUTDOWN mode from the decoder will disable the termination regardless of TERM_OFF. LOOPBACK FUNCTION The SP508 contains a LOOPBACK pin that invokes a loopback path. This loopback path is illustrated in Figure 50. LOOPBACK has an internal pull-up resistor that defaults to normal mode during power up or if the pin is left floating. During loopback, the driver output and receiver input characteristics will still adhere to its appropriate specifications. DECODER AND D_LATCH FUNCTION The SP508 contains a D_LATCH pin that latches the data into the D0, D1, and D2 decoder inputs. If tied to a logic LOW ("0"), the latch is transparent, allowing the data at the decoder inputs to propagate through and program the SP508 accordingly. If tied to a logic HIGH("1"), the latch locks out the data and prevents the mode from changing until this pin is brought to a logic LOW.
There are internal pull-up devices on D0, D1, and D2, which allow the device to be in SHUTDOWN mode ("111") upon power up. However , if the device is powered -up with the D_LATCH at a logic HIGH, the decoder state of the SP508 will be undefined. ESD TOLERANCE The SP508 device incorporates ruggedized ESD cells on all driver output and receiver input pins. The ESD structure is improved over our previous family for more rugged applications and environments sensitive to electrostatic discharges and associated transients. CTR1/CTR2 EUROPEAN COMPLIANCY As with all of Sipex's previous multi-protocol serial transceiver IC's the drivers and receivers have been designed to meet all the requirements to NET1/NET2 and TBR2 in order to meet CTR1/CTR2 compliancy. The SP508 is also tested in-house at Sipex and adheres to all the NET1/2 physical layer testing and the ITU Series V specifications before shipment. Please note that although the SP508 , as with its predecessors, adhere to CTR1/CTR2 compliancy testing, any complex or unusual configuration should be double-checked to ensure CTR1/CTR2 compliance. Consult the factory for details.
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
24
SD(a) TxD SD(b)
RD(a) RxD RD(b) TT(a) TxCE TT(b)
RT(a) RxC RT(b) ST(a) ST ST(b)
TxC(a) TxC TxC(b) RS(a) RTS RS(b)
CS(a) CTS CS(b) TR(a) DTR TR(b)
DM(a) DSR DM(b) RRC(a) DCD_DCE RRC(b)
RRT(a) DCD_DTE RRT(b)
RL
RL(a)
RI
IC
LL
LL(a)
TM
TM(a)
Figure 46. SP508 Loopback Path
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
25
1F 1F
1F
+5V
10F
VDD VCC C1+ VSS C1- C2+ C2-
Date: 8/19/04
1F Charge Pump Section Transceiver Section
DB-26 Serial Port Connector Pins Signal (DTE_DCE)
#103 (TxD) #113 (TXCE)
ST RTS DTR DCD_DCE
DCE
TxD TxCE
2 (V.11, V.35, V.28) 14 (V.11, V.35) 24 (V.11, V.35, V.28) 11 (V.11, V.35)
TXD_RXD_A TXD_RXD_B TXCE_TXC_A TXCE_TXC_B
#105 (RTS) #108 (DTR) #109 (DCD) #140 (RL) #141 (LL)
LL RL
4 (V.11, V.28) 19 (V.11) 20 (V.11, V.28) 23 (V.11)
RTS_CTS_A RTS_CTS_B DTR_DSR_A DTR_DSR_B
21 (V.10, V.28) 18 (V.10, V.28)
RL_RI LL_TM
#105 (RXD) #115 (RXC) #114 (TxC) #106 (CTS) #107 (DSR) #109 (DCD)DTE #125 (RI) #142 (TM)
TM Logic Section RI DCD_DTE DSR CTS TxC RxC
RxD
Figure 47. SP508 Typical Operating Configuration to Serial Port Connector with DCE/DTE programmability
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
3 (V.11, V.35, V.28) 16 (V.11, V.35) 17 (V.11, V.35, V.28) 9 (V.11, V.35) 15 (V.11, V.35, V.28) 12 (V.11, V.35) 5 (V.11, V.28) 13 (V.11) 6 (V.11, V.28) 22 (V.11) 8 (V.11, V.28) 10 (V.11) 22 (V.10, V.28) 25 (V.10, V.28)
D0 D1 D2 D_LATCH TERM_OFF LOOPBACK V35TGND1 V35TGND2 V35TGND3 V35RGND V10_GND GND RDEN RTEN TxCEN DMEN CSEN RRTEN ICEN TMEN
26
+5V
RXD_TXD_A RXD_TXD_B RXC_TXCE_A RXC_TXCE_B *TXC_RXC_A *TXC_RXC_B CTS_RTS_A CTS_RTS_B DSR_DTR_A DSR_DTR_B DCD_DCD_A DCD_DCD_B RI_RL LL_TM
DCE/DTE
SP509CF
SDEN TTEN STEN TREN RSEN RRCEN RLEN LLEN
+5V
* - Driver applies for DCE only on pins 15 and 12. Receiver applies for DTE only on pins 15 and 12. Driver applies for DCE only on pins 8 and 10. Receiver applies for DTE only on pins 8 and 10.
SIGNAL GND (10 Pins)
Reference Design Schematic
Customer : Title : Date :
233 South Hillview Dr. * Milpitas, CA. 95035
Input Line Output Line I/O Lines represented by double arrowhead signifies a bi-directional bus.
Typical SP509 DB-26 Serial Port Configuration
Doc. # :
Rev.
(c) Copyright 2004 Sipex Corporation
0
PACKAGE: 100 Pin LQFP
D D1
0.2 RAD MAX. c 0.08 RAD MIN.
PIN 1 11-13 0MIN C L E1 E 0-7 11-13 L L1 C L A2 b
DIMENSIONS Minimum/Maximum (mm) SYMBOL A A1 A2 b D D1 e E E1 N 0.05 1.35 0.17 1.40 0.22
A A1 e
100-PIN LQFP JEDEC MS-026 (BED) Variation MIN NOM MAX 1.60 0.15 1.45 0.27
Seating Plane
COMMON DIMENSIONS SYMBL MIN c L L1 0.09 0.45 0.60 1.00 REF NOM MAX 0.20 0.75
16.00 BSC 14.00 BSC 0.50 BSC 16.00 BSC 14.00 BSC 100
100 PIN LQFP
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
27
SP508 Multiprotocol Configured as DCE Interface to PortConnector Interface to System Logic Pin Pin Pin Mnemonic Number Circuit Number Pin Mnemonic 97 SD(A) Driver_1 TxD 28 100 SD(B) SDEN 3 92 TT(A) TxCE Driver_2 29 95 TT(B) TTEN 4 87 ST(A) ST 30 Driver_3 90 ST(B) STEN 5 83 RS(A) RTS 31 Driver_4 85 RS(B) RSEN 6 75 TR(A) DTR 32 Driver_5 78 TR(B) TREN 7 81 RRC(A) DCD_DCE 33 Driver_6 79 RRC(B) RRCEN 8 65 RL(A) RL 34 Driver_7 RLEN 9 63 LL(A) LL 35 Driver_8 LLEN# 10 48 RD(A) RxD 36 Receiver_1 47 RD(B) RDEN# 11 50 RT(A) RxC 37 Receiver_2 49 RT(B) RTEN# 12 53 TxC(A) TxC 38 Receiver_3 51 TxC(B) TxCEN# 13 55 CS(A) CTS 39 Receiver_4 54 CS(B) CSEN# 14 57 DM(A) DSR 40 Receiver_5 56 DM(B) DMEN# 15 60 RRT(A) DCD_DTE 41 Receiver_6 59 RRT(B) RRTEN# 16 61 IC RI 42 Receiver_7 ICEN# 17 62 TM(A) TM 43 Receiver_8 TMEN 18 Spare drivers and receivers may be used for optional signals (Signal Quality, Rate Detect, Standby) or may be disabled using individual enable pins for each driver and receiver
Recommended Signals and Port Pin Assignments X.21 V.35 RS-449 EIA-530 RS-232 or V.24 Signal Mnemo DB-25 Signal Mnemo DB-25 Signal Mnemo DB-37 Signal Mnemo M34 Signal Mnemo DB-15 Pin(F) nic Pin(F) Type nic Pin(F) Type nic Pin(F) Type nic Pin(F) Type nic Type 4 R(A) V.11 R 104 V.35 6 V.11 RD(A) 3 V.11 BB(A) 3 BB V.28 11 R(B) V.11 T 104 V.35 24 V.11 RD(B) 16 V.11 BB(B) 7** B(A) V.11 V 115 V.35 8 V.11 RT(A) 17 V.11 DD(A) 17 DD V.28 14** B(B) V.11 X 115 V.35 26 V.11 RT(B) 9 V.11 DD(B) 6 S(A) V.11 Y 114 V.35 5 ST(A) V.11 15 V.11 DB(A) 15 DB V.28 13 S(B) V.11 AA 114 V.35 23 ST(B) V.11 12 V.11 DB(B) 5 I(A) V.11 D 106 V.28 9 V.11 CS(A) 5 V.11 CB(A) 5 CB V.28 12 I(B) V.11 27 V.11 CS(B) 13 V.11 CB(B) E 107 V.28 11 V.11 DM(A) 6 V.11 CC(A) 6 CC V.28 29 V.11 DM(B) 22 V.11 CC(B) F 109 V.28 13 V.11 RR(A) 8 V.11 CF(A) 8 CF V.28 31 V.11 RR(B) 10 V.11 CF(B) J 125 V.28 22 CE V.28 V.28 V.28 V.28 TM BA DA 25 2 24 V.10 V.11 V.11 V.11 V.11 TM BA(A) BA(B) DA(A) DA(B) 25 2 12 24 11 V.10 V.11 V.11 V.11 V.11 TM SD(A) SD(B) TT(A) TT(B) 18 4 22 17 35 V.28 V.35 V.35 V.35 V.35 142 103 103 113 113 NN P S U W V.11 V.11 V.11 V.11 T(A) T(B) X(A) X(B) 2 9 7** 14**
SP508 Enhanced WAN Multi-Protocol Serial Transceiver Date: 8/19/04
(c) Copyright 2004 Sipex Corporation
DCE CONFIGURATION
V.28 V.28
CA CD
4 20
V.11 V.11 V.11 V.11
CA(A) CA(B) CD(A) CD(B)
4 19 20 23
V.11 V.11 V.11 V.11
RS(A) RS(B) TR(A) TR(B)
7 25 12 30
V.28 V.28
105 108
C H
V.11 V.11
C(A) C(B)
3 10
V.28 V.28
RL LL
21 18
V.10 V.10
RL LL
21 18
V.10 V.10
RL LL
14 10
V.28 V.28
140 141
N L
Pin assignments and signal functions are subject to national or regional variation and proprietary / non-standard implementations
** X.21 use either B() or X(), not both
Date: 6/14/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
28
28
Interface to System Logic Pin Number 28 3 29 4 30 5 31 6 32 7 33 8 34 9 35 10 36 11 37 12 38 13 39 14 40 15 41 16 42 17 43 18
SP508 Multiprotocol Configured as DTE Interface to PortConnector Circuit Driver_1 Driver_2 Driver_3 Driver_4 Driver_5 Driver_6 Driver_7 Driver_8 Receiver_1 Receiver_2 Receiver_3 Receiver_4 Receiver_5 Receiver_6 Receiver_7 Receiver_8 Pin Mnemonic SD(A) SD(B) TT(A) TT(B) ST(A) ST(B) RS(A) RS(B) TR(A) TR(B) RRC(A) RRC(B) RL(A) LL(A) RD(A) RD(B) RT(A) RT(B) TxC(A) TxC(B) CS(A) CS(B) DM(A) DM(B) RRT(A) RRT(B) IC TM(A) Pin Number 97 100 92 95 87 90 83 85 75 78 81 79 65 63 48 47 50 49 53 51 55 54 57 56 60 59 61 62
Recommended Signals and Port Pin Assignments RS-232 or V.24 EIA-530 DB-25 Pin(M) 2 14 24 11 RS-449 Signal Mnemo nic Type V.11 SD(A) V.11 SD(B) TT(A) V.11 TT(B) V.11 DB-37 Pin(M) 4 22 17 35 V.35 Signal Mnemo M34 Pin(M) nic Type P 103 V.35 S 103 V.35 U 113 V.35 W 113 V.35 X.21 Signal Mnemo DB-15 Pin(M) nic Type 2 T(A) V.11 9 T(B) V.11 7** X(A) V.11 14** X(B) V.11 Signal Type V.11 V.11 AppleTalkTM Mnemo nic TxD TxD + DIN-8 Pin(F) 3 6
Pin Mnemonic TxD SDEN TxCE TTEN ST STEN RTS RSEN DTR TREN DCD_DCE RRCEN RL RLEN LL LLEN# RxD RDEN# RxC RTEN# TxC TxCEN# CTS CSEN# DSR DMEN# DCD_DTE RRTEN# RI ICEN# TM TMEN
Signal Mnemo DB-25 Signal Mnemo nic Pin(M) Type nic Type BA(A) V.11 2 BA V.28 BA(B) V.11 V.11 DA(A) 24 DA V.28 V.11 DA(B)
V.28 V.28
CA CD
4 20
V.11 V.11 V.11/10 V.11/Z
CA(A) CA(B) CD(A) CD(B)
4 19 20 23
V.11 V.11 V.11 V.11
RS(A) RS(B) TR(A) TR(B)
7 25 12 30
V.28 V.28
105 108
C H
V.11 V.11
C(A) C(B)
3 10 V.10 HSKo 1
V.28 V.28 V.28 V.28 V.28 V.28 V.28 V.28 V.28 V.28
RL LL BB DD DB CB CC CF CE TM
21 18 3 17 15 5 6 8 22 25
V.10 V.10 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11/10 V.11/Z V.11 V.11 V.10 V.10
RL LL BB(A) BB(B) DD(A) DD(B) DB(A) DB(B) CB(A) CB(B) CC(A) CC(B) CF(A) CF(B) RI TM
21 18 3 16 17 9 15 12 5 13 6 22 8 10 22 25
V.10 V.10 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11 V.11
RL LL RD(A) RD(B) RT(A) RT(B) ST(A) ST(B) CS(A) CS(B) DM(A) DM(B) RR(A) RR(B)
14 10 6 24 8 26 5 23 9 27 11 29 13 31
V.28 V.28 V.35 V.35 V.35 V.35 V.35 V.35 V.28 V.28 V.28 V.28
140 141 104 104 115 115 114 114 106 107 109 125 142
N L R T V X Y AA D E F J NN V.11 V.11 R(A) R(B) 4 11 V.11 V.11 RxDRxD+ 5 8
SP508 Enhanced WAN Multi-Protocol Serial Transceiver Date: 8/19/04
(c) Copyright 2004 Sipex Corporation
DTE CONFIGURATION
V.11 V.11 V.11 V.11 V.11 V.11
S(A) S(B) I(A) I(B) B(A) B(B)
6 13 5 12 7** 14**
V.10* V.10
GND HSKi GPi
2 7
V.10
TM
18
V.28
Spare drivers and receivers may be used for optional signals (Signal Quality, Rate Detect, Standby) or may be disabled using individual enable pins for each driver and receiver
Pin assignments and signal functions are subject to national or regional variation and proprietary / non-standard implementations EIA-530 uses V.11 (differential) for DSR (CC) and DTR (CD) signals; EIA-530-A uses singleended V.10 for DSR and DTR and adds RI signal on pin 22
** X.21 use either B() or X(), not both
DDate: 6/14/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
29
29
ORDERING INFORMATION
Part Number Top Mark Temperature Range Package Types SP508CF ...................... SP508CFYYWW..........................0C to +70C .............................. 100 Lead LQFP SP508EF ...................... SP508EFYYWW.......................-40C to +85C .............................. 100 Lead LQFP Available in lead free packaging. To order add "-L" suffix to part number. Example: SP508EF/TR = standard; SP508EF-L/TR = lead free
REVISION HISTORY
DATE 3/31/04 5/6/04 6/3/04 8/19/04 REVISION A B C D DESCRIPTION Implemented tracking revision. Added Top Mark to ordering information. Added Tables to page 28 and 29. Corrected pin description table and figure 49. Updated DCE/DTE tables.
Corporation
ANALOG EXCELLENCE
Sipex Corporation Headquarters and Sales Office 233 South Hillview Drive Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) 935-7600
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.
Date: 8/19/04
SP508 Enhanced WAN Multi-Protocol Serial Transceiver
(c) Copyright 2004 Sipex Corporation
30

▲Up To Search▲

Price & Availability of SP508

	To Download SP508 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .